• FlashKit 2.9 - in batch programming when verification fails due different data in the Flash, errorlevel reported success (value 0) although text description was correct . Fixed. In batch programming added new errorlevel nr. 13 for I/O error (creating files, etc.). See multiflash.bat.
• The support for the following CPUs was added: MB90F548G, MB90F562B, MB90F497G, MB90F543G, MB90F546G
  Note: The CPUs with the "G" postfix support to change the PLL setting also in the serial programming mode. Therefore, these CPUs support higher baud rates in the asynchronous mode. The MB90F562B CPU supports the "Flash security" feature (which is not supported by the standard MB90F562 version)
• The new "Speed" option was added to the main window. This allows to select the baud rate for all devices, which can change the PLL setting in serial programming mode.
• When the "Auto program" or "Write file" function is invoked, the date&time of the file is checked. If it is different from the last time, the file is reloaded automatically.
• The "External watchdog triggering" function was added (see menu Options|Settings, tab "Synchronous" - option "Trigger pulses"). If enabled, the watchdog trigger pulses are generated on the pin PIO1 of the box programming connector. With these pulses, an external watchdog on the user target board can be triggered, so the programming is possible even when the external watchdog HW is enabled during the programming of the CPU.
• New option "CPU Operating Mode after Auto Program" was added (see menu Options|Settings, tab "Synchronous"). This option allows to select the CPU operating mode after the Auto Program function is finished. The possible CPU modes are: "Single chip mode", "Programming mode" and "Tristate".
• Workaround solution for the "Pulldown on MD2" issue was implemented in this version. The "Pulldown on MD2" issue concerns the user target boards, which have a hard-wired pulldown < 50kO connected to the MD2 CPU line. It was impossible to program such boards in synchronous mode using the older version of FlashKit programmer, because the serial programmer box open-collector driver of the MD2 line could not set the voltage of such a MD2 line to the "high" level. The workaround solution uses a modified programming cable. The description of this solution can be found in the Appendix B of the FlashKit manual.
• Workaround solution for the "Pulldown on MD2" issue plus "CPU Operating Mode after Auto Program" was implemented also for command line programming.

Please read complete installation notes before installation.

• Fix in CANchannel bean - corrections in interrupt routines, LEIR register is not used now to determine what message buffer caused the last event

• the MB90F546, Flash size bug fixed - 128kB instead 256kB, so it was impossible to program whole Flash Memory for this chip.

This package contains a full InstallShield installation of FlashTool 1.4. Using this file, you can install FlashTool 1.4 as a standalone tool, that will be accessible through the Start menu.

IMPORTANT NOTE: If you have Processor Expert (PE) with FlashTool already installed on your computer, you can either update that older version of FlashTool by choosing the PE installation directory as a installation target when installing this new FlashTool, or you can install the new FlashTool into another directory. Then, the older version will stay untouched. However, when accessing FlashTool from the PE "Tools" menu, the OLDER version will be called !!! For more information about this update see here.

If CAN interface is not used in the DevKit16 and the appropriate CPU I/O pins (which are connected though the jumpers to the CAN chip - default setting) are used as a general I/O pins, it is necessary to remove these jumpers as follows:

jumper J24 - position 5-6
jumper J25 - position 5-6

It means that the pins P95 and P97 on the CPU 543 and pin P44 on the CPU 497 will not be connected to the CAN chip (82C250). It is important to disconnect these pins, because the unused CAN chip can damage the connected device to the port.

This is an update of the Processor Expert 2.40. It solves the problem of initialized C variables marked with directive __direct.

See installation instructions: How to install update package.

This is an update of the IntFlash bean. It fixes the bug that disallow to program the internal flash in the single chip mode. Note: This update is intended for all users of the PE 2.39 and previous versions.

See installation instructions: How to install update package.

This update contains new version of Processor Expert Debug kernels for DevKit16 (version 1.4). These kernels can be used with Processor Expert 2.40 (and higher) with DevKit16 and FlashTool 1.31. Bug in interrupt service routine was fixed (for Softune C Compiler SMALL model).
Kernels with different PLL settings are also included in the package (x1, x2, default x4). After installation you can find them in the directory \Config\FlashTool\FujitsuDevKit16\.
Supported MCUs: Fujitsu MB90543, MB90497.

See installation instructions: How to install update package.
After installation you must burn new debug kernlel into DevKit16 external FLASH using FlashTool or command from Processor Expert Tools menu.

This update contains all previous updates (Enhanced Embedded Beans, FlashTool updates ...) except documentation.
Note: This version is intended for Processor Expert for MB90F543 CPU only.

Installation: Unzip the update files into your Processor Expert directory. Overwrite old files. Preserve directory structure from the zipped file.

Recommended: For detailed description please read this

This package contains a full InstallShield installation of FlashTool 1.31. Using this file, you can install FlashTool 1.31 as a standalone tool, that will be accessible through the Start menu.

IMPORTANT NOTE: If you have Processor Expert (PE) with FlashTool already installed on your computer, you can either update that older version of FlashTool by choosing the PE installation directory as a installation target when installing this new FlashTool, or you can install the new FlashTool into another directory. Then, the older version will stay untouched. However, when accessing FlashTool from the PE "Tools" menu, the OLDER version will be called !!!

NOTE FOR FLASHTOOL 1.2 (or 1.3) USERS: If you have FlashTool 1.2 (or 1.3) installed then you may only download zipped updated file - click on the icon below for download.
For more information about this update see here.

This version (1.31) replaces FlashTool 1.2 released in update of Processor Expert to version 2.38.

This update contains all previous updates (Enhanced Embedded Beans, FlashTool updates ...) except documentation.

Installation: Unzip the update files into your Processor Expert directory. Overwrite old files. Preserve directory structure from the zipped file.

Recommended: For detailed description please read this.